Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across San Bernardino
Electric gate repair in San Bernardino typically runs $185 – $650 for most motor, control board, and hinge work, with same-week scheduling available for most residential calls. We’re a gate-only shop based in Chino, and our Electric Gate Repair technicians know the Inland Empire’s specific failure patterns cold. If you’re off Waterman Avenue, up near the foothills in the North End, or in a 1950s tract home in the 92404 ZIP code, we can diagnose what’s actually wrong with your gate and give you a written price before any work starts. Call (833) 545-6817 for a free estimate.
Why Wrought Gate Repair Is San Bernardino’s Preferred Electric Gate Repair Company
We work exclusively on gates. That’s not a slogan; it’s the entire scope of what we do. Every van, every part shelf, every technician’s training is focused on gate repair, electric gate repair, and installation, and nothing else. A general handyman might patch a hinge and call it fixed. We find the underlying reason the gate failed, address it, and stand behind the work.
Our owner, Ruben Castellano, built Wrought Gate Repair around a simple idea: San Bernardino homeowners with a dead FAAC operator or a sagging 1960s swing gate shouldn’t have to bounce between a fence company, an electrician, and a locksmith to get one problem solved. One call covers it. We service nine major gate automation brands including FAAC, BFT, and Linear, so when we pull into a driveway near Blair Park or a commercial property along E Street, we’re not guessing at the operator. We know it.
San Bernardino’s gate problems are shaped by specific local conditions: months of 100°F-plus heat, constant sun, Santa Ana wind, and grit blowing off the San Bernardino Mountains. Those forces destroy gate hardware faster than almost anything else. We see it weekly in 92401, 92403, and 92404. We schedule by neighborhood cluster, which lets us reach most San Bernardino addresses for a service call faster than a shop that has to dispatch from Riverside or Rancho Cucamonga.
Styles & brands we work with
Electric Gate Motor in San Bernardino
An Electric Gate Motor failure in San Bernardino usually shows up as a gate that hums but won’t move, moves halfway and stops, or trips its breaker repeatedly, especially on hot afternoons. Summer heat pushes older operators past their thermal limits. We replace swing and slide gate motors across the city, from mid-century properties near Loma Linda’s border to newer communities on the city’s east edge.
A swing gate motor replacement in San Bernardino runs $350 – $850 including labor. Slide gate motor replacement runs $450 – $1,100 depending on the operator’s weight capacity and whether the existing motor’s mounting plate can be reused. We stock motors compatible with LiftMaster, FAAC, BFT, Linear, and Viking systems, so most replacements don’t need a special order.
When Retrofit Makes Sense
If your motor is fried but the gate itself and the hinge posts are structurally sound, retrofitting a new operator onto the existing ironwork is often the best value. We’ve done it on dozens of homes near the foothills where the original gate was built to last, but the operator from 15 years ago gave out.
Operator Replacement for Legacy Systems
Older slide gate operators, particularly units from the 1980s and 1990s, often can’t be economically repaired because their control boards are obsolete and the motor windings are heat-damaged from repeated San Bernardino summers. In those cases, replacement is straightforward, and we price it before touching anything.
Gate Access Control in San Bernardino
Gate Access Control in San Bernardino covers the keypads, remote receivers, safety sensors, and control boards that tell your gate when to open and close safely. It’s the most common failure point we address, and in this climate, it’s usually heat or dust doing the damage. Keypad and access control repair runs $125 – $325 for most jobs, including labor and the replacement part.
San Bernardino’s wind-blown grit works into keypad compartments and sensor housings. Contacts corrode. Buttons become unresponsive. On properties near the foothills where dust is constant, we recommend sealing gaskets during any access control repair, something most general repair companies never mention. It’s the kind of detail that comes from working on gates here, not just reading a service manual.
Keypad and Remote Upgrades
We can add a new keypad or remote receiver to almost any gate system, including older manual gates that are being automated for the first time. If your keypad’s display is faded from direct sun on a south-facing install, replacement is usually quick and inexpensive.
Safety Sensor Replacement
UL 325 requires safety photocells on automated gates, and older San Bernardino systems often lack them or have failed ones. We install and align safety sensors so the gate stops and reverses when a vehicle or person crosses the beam. This is also part of our retrofits when a legacy operator is replaced.
Trusted Brands We Service in San Bernardino
Whether your operator is a FAAC swing arm, a BFT underground unit, or a Linear slide-gate drive, our technicians service it in San Bernardino and the surrounding Inland Empire. We keep common control boards, keypads, remotes, and safety components on hand for these and other major brands, which means less waiting for parts and fewer return trips. If your system is an older model and the exact board isn’t made anymore, we’ll tell you upfront and price a compatible retrofit honestly.
Common Electric Gate Repair Problems We See in San Bernardino Homes
- Gate reverses randomly mid-cycle. This is often an obsolete control board failing in the heat. On a recent job in the North End, a mid-century swing gate reversed unpredictably because its original 1960s-era board was heat-sensitized. We reinforced the hinge post footing and installed a modern LiftMaster operator with safety photocells to bring the system current.
- Sagging gates that drag and strain the motor. San Bernardino’s dry, sandy soil near the foothills doesn’t hold hinge posts firmly. A post that’s shifted even an inch causes sag, and the operator works harder and dies sooner. We correct sag by reinforcing the post footing, then repair or replace the operator as needed.
- Slide gate binding and false activations. Wind-blown grit from the mountains gets into tracks and loop detectors. The gate grinds, or the loop detector sees a phantom vehicle and cycles the gate for no reason. Regular cleaning and dielectric greasing on terminals is the fix most of the time.
- Wrought iron rust and hinge wear from UV exposure. Gates on south and west sides of San Bernardino homes take constant sun. Finish fades, paint fails, and hinges wear at an accelerated rate. We replace worn hinges and can repair rusted sections without losing the original ironwork.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in San Bernardino, CA
We quote every job before work starts, and the price we give is the price you pay. Here’s what San Bernardino homeowners typically see for common repairs:
- Control board replacement: $185 – $420
- Safety sensor installation or replacement: $90 – $180 per pair
- Keypad or remote receiver replacement: $125 – $325
- Swing gate motor replacement: $350 – $850
- Slide gate motor replacement: $450 – $1,100
- Hinge replacement (iron or steel gate): $150 – $400 per hinge
- Sag correction with post reinforcement: $300 – $700
What moves the number: the age and brand of your operator, whether the mounting hardware is reusable, and whether we’re correcting post or hinge problems before installing a new motor. For a free written estimate specific to your gate, call (833) 545-6817.
We Also Serve Cities Near San Bernardino
Our service area covers San Bernardino and the surrounding Inland Empire, including Muscoy, Highland, Loma Linda, and Rialto. If you’re just over the city line in Rialto or up the 210 in Highland, we’re already working in your area every week.
Serving San Bernardino, CA — Our Local Coverage Area
We’re based in the San Bernardino area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in San Bernardino
In most cases, yes. When an older slide gate operator’s breaker trips during heat, the control board’s capacitors have usually degraded from years of 100°F-plus summers. We can often retrofit a modern control board and retain the existing motor if it’s still functioning correctly. The cost ranges from $185 – $420. If the motor itself has also heat-damaged windings, a full operator replacement is usually the better value. Call (833) 545-6817 and we’ll give you an honest assessment.
Yes. Safety photocells detect a vehicle, person, or pet in the gate’s path and stop or reverse the gate before contact. UL 325 requires them on automated gate operators, and installing a pair in San Bernardino runs $90 – $180. This is a small investment for safety and liability protection, and it’s part of every legacy operator retrofit we do.
Often neither. The problem is usually the hinge post, not the operator or the gate’s structure. San Bernardino’s dry foothill soil doesn’t hold posts securely over time, and a leaning post causes the entire gate to sag. We reinforce the post footing and correct the hang, which costs $300 – $700, then test the operator to see if it’s still viable. Many times it is. If the operator has been straining for months, it may need replacement too, but we’ll test before we recommend spending money.
Wind-blown grit from the mountains works into slide gate tracks and loop detector housings. The rack and pinion grinds and wears prematurely. Loop detectors can false-activate when conductive dust accumulates. Regular cleaning, track lubrication with the correct dry-film product for desert environments, and applying dielectric grease to loop detector terminals are the main defenses. This is a bigger issue in foothill neighborhoods and homes on the north end of town where prevailing winds push sand directly into gate mechanisms.
Yes, in most cases. Wrought iron gates from the 1950s were often built heavier than modern counterparts, and the iron itself is frequently still sound. We replace rusted sections, repair or replace worn hinges, and address post issues without scrapping the original gate. When a customer in the North End needed work on their original mid-century swing gate, we kept the original ironwork and brought the automation up to modern safety standards. The gate will outlast its second operator.
Call Wrought Gate Repair for Electric Gate Service in San Bernardino
Your gate is either a working opening or a liability. In San Bernardino, where the climate punishes gate hardware year-round, a specialist’s eye saves you money and keeps your property secure. We’re the company that does gates and only gates. Call (833) 545-6817 today for a free estimate on electric gate motor repair, access control replacement, or a full legacy system retrofit. We’ll give you a written price before any work begins.
Written by Ruben Castellano, Owner at Wrought Gate Repair, serving San Bernardino and the Inland Empire.