Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across San Clemente
Gate repair in San Clemente usually costs $180 to $850 depending on whether you’re dealing with a rusted hinge, a failed control board, or a full operator retrofit, and most residential calls we handle are done in a single visit. Salty air from the Pacific cuts through wrought iron and electronics faster here than almost anywhere else in Orange County, so the trick isn’t just fixing what broke. It’s fixing it so it doesn’t fail again in eighteen months. We work exclusively on gates, and we’ve seen every failure mode the San Clemente climate can produce. Call us at (833) 545-6817 and we’ll get someone to your gate, usually within a day or two for non-emergency work.
Our team is led by Ruben Castellano, and we don’t split our attention across fences, garage doors, or general contracting. Gates are the whole job. That focus matters when you’re dealing with a Viking swing arm that’s been soaking in marine layer moisture, or a 20-year-old wrought iron gate that’s sagged past the point where the latch catches cleanly.
Why Wrought Gate Repair Is San Clemente’s Preferred Gate Repair Company
We’ve earned our reputation in San Clemente by fixing what other contractors walk away from. A corroded FAAC control board in a hillside driveway off Camino De Los Mares isn’t a curiosity to us. It’s Tuesday. Homeowners in 92672, 92673, and 92674 call because we diagnose the actual failure instead of swapping parts on a guess.
Our technicians carry parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. That’s nine major gate automation brands under one roof. If your HOA in Marblehead specifies a particular bronze finish or your Talega gate needs a replacement hinge that matches the community’s approved palette, we handle that without handoffs or referrals out. One call covers it.
Ruben Castellano built this company around a simple idea: a gate specialist should be able to fix anything with hinges, tracks, motors, or control boards. Whether you have a manual wrought iron gate from the 1970s or a modern automatic driveway gate, our team has the diagnostic discipline and the local parts access to get it right the first time.
Styles & brands we work with
Sliding Gate Repair in San Clemente
Sliding gate repair in San Clemente typically runs between $350 and $950, depending on whether the problem is a failed roller assembly, a bent track, a worn motor, or a control board that’s given up after years of salt exposure. Coastal properties in 92672 and 92673 see sliding gate failures earlier than inland homes because the marine layer pushes moisture into the operator housing and corrodes the terminal connections. We see it constantly.
In San Clemente, sliding gates are common on hillside lots where a swing gate would need too much uphill clearance to be practical. The tradeoff is that slide tracks collect debris and salt residue, and rollers wear faster when the gate’s alignment drifts even slightly. Fixing it right means diagnosing the root cause, not just greasing the track and hoping.
Canvas Canopy and Track Alignment
A sliding gate that shudders or sticks partway through its travel usually has a track issue. Salt and grit bind in the rollers, the track shifts with Santa Ana wind pressure, and the gate starts fighting the motor. We correct the track alignment, replace worn rollers, and set the gate’s travel limits so the operator isn’t straining on every cycle.
Operator and Control Board Failure
When a slide gate stops responding to the remote or the keypad, the operator’s control board is often the culprit. Coastal moisture inside the housing creates green corrosion on the terminals, and the board eventually shorts out. We stock replacement boards for all nine brands we service, and we apply coastal-grade dielectric protection to the new connections. A retrofit on an older slide gate with obsolete controls is often cheaper than repeated board failures on a system that was never designed for salt air.
Wrought Iron Gate Repair in San Clemente
Wrought iron gate repair in San Clemente typically costs between $250 and $700, with rust remediation, hinge replacement, and sag correction accounting for most of the calls we take in 92673 and inland zones. The irony of wrought iron in a coastal town is that it’s beautiful and durable right up until the salt air finds a pinhole in the paint. Then the rust spreads underneath the coating, and one hinge starts carrying more weight than it was built for.
Older San Clemente homes, especially the mid-century beach bungalows along the Avenida corridor and the 1970s-80s tract homes east of I-5, often have original steel or wrought iron gates that were hung decades before modern coating systems existed. We repair the gate, then we treat it so the same repair doesn’t come back after one foggy season.
Rust Remediation and Coastal-Grade Coating
Salt-air corrosion is the single biggest killer of wrought iron gates in coastal ZIP codes 92672 and 92673. We grind out the rust, repair or replace the affected sections, and apply a coastal-grade primer and finish that stands up to daily marine layer exposure. For gates with ornamental scrollwork, we take care to preserve the original profile while cutting out the rot.
Hinge Post and Sag Correction
A wrought iron gate that drags on the ground or won’t latch anymore usually has a hinge post problem, not a gate problem. Inland Santa Ana winds push against the gate’s full sail area, and over years, the post loosens in its footing. We reset the post with proper anchoring and realign the gate so it swings true. If the hinges themselves are worn or corroded, we replace them. Your gate, fixed right.
Trusted Brands We Service in San Clemente
We service nine major gate automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters in San Clemente because homeowners and property managers here don’t want to track down a brand-specific dealer when a control board fails or an arm actuator starts grinding. We keep common parts for FAAC, BFT, Linear, and Viking systems on our trucks for San Clemente calls, so we can often complete the repair in a single trip. Solar gate openers, swing arms, slide operators, keypads, and loop detectors are all in our scope. If you know your gate uses a BFT or a Linear operator, tell us when you call and we’ll bring the right parts.
Common Gate Repair Problems We See in San Clemente Homes
- Salt-air corrosion on coastal properties: Wrought iron and galvanized hardware in 92672 and 92673 pit and rust far faster than a few miles inland. Control boards inside operator housings fail prematurely from marine layer moisture even when the gate itself looks fine. We treat both the structure and the electronics.
- Sagging gates from Santa Ana wind stress: Inland hillside properties deal with hot, dry wind events that loosen hinge posts and stress wood and metal alike. A gate that sags catches on the ground, misaligns with the loop detector, and stops responding to the keypad. We reset posts and correct the hang.
- Obsolete control boards: Many San Clemente gates were installed before modern UL 325 entrapment protection requirements existed. Older boards fail, and when you replace them, you often discover the safety photocells and edge sensors were never installed. We can retrofit those systems while fixing the board.
- HOA compliance issues in Talega and Marblehead: In Talega, Marblehead, and other master-planned communities, gate repairs often require matching the community’s approved color and style palette. A generic galvanized replacement or an off-color repair can trigger a compliance notice. Local techs who work these neighborhoods keep the HOA paint specs on hand, and so do we.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in San Clemente, CA
Here’s what gate repair costs in San Clemente, based on the work we actually do here.
| Service | Typical San Clemente Range |
|---|---|
| Wrought iron gate repair (hinge, sag, or rust remediation) | $250 – $700 |
| Sliding gate repair (track, roller, or motor) | $350 – $950 |
| Control board replacement (any brand) | $280 – $600 |
| Hinge and post repair | $180 – $450 |
| Full operator retrofit (old gate, modern safety compliance) | $800 – $2,400 |
The quote we give you before we start is the price you pay. We don’t bill up from an estimate. If we find something unexpected during the repair, we stop and talk to you first. Estimates are free. Call (833) 545-6817 and we’ll walk you through what your specific gate needs.
We Also Serve Cities Near San Clemente
Our service area extends beyond San Clemente to Ladera Ranch, Laguna Beach, Laguna Hills, and Coto De Caza. If you’re on the border of any of those communities, Gate Repair in San Clemente coverage often includes you. We know the streets, the HOAs, and the gate systems common to each area.
Serving San Clemente, CA — Our Local Coverage Area
We’re based in the San Clemente area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in San Clemente
Yes. We regularly retrofit gates that were installed before UL 325 entrapment protection requirements existed. That means adding or replacing safety photocells, edge sensors, and control boards to bring an automated gate up to current standards. On some older operators, a retrofit is cost-effective and completely feasible; on others, replacing the operator with a modern unit is the cheaper long-term answer. We’ll tell you honestly which direction makes sense for your specific gate. Call (833) 545-6817 and we’ll assess it for free.
The most effective protection for coastal gates in 92672 is a coastal-grade coating system applied over properly prepped metal, combined with dielectric protection on all electrical connections inside the operator housing. We see less corrosion damage on gates where the owner schedules a quick inspection every year or two, especially after the foggy spring months. If your gate already shows rust, the time to treat it is now, before it spreads behind the paint. Call (833) 545-6817 for an exact quote on rust remediation.
Yes, and this comes up constantly in San Clemente’s HOA communities like Talega and Marblehead. We keep the common HOA paint specs and finish palettes on hand for these neighborhoods, and we can match your community’s approved color when we paint or refinish a repaired section. If we’re replacing hardware like hinges or a latch, we can source finishes that blend with the approved aesthetic rather than standing out. If your HOA has a specific finish requirement, just tell us when you call. Call (833) 545-6817 and mention your community’s name.
Gate sag is almost always a hinge post issue, not a structural failure of the gate itself. In San Clemente, Santa Ana winds push against the gate’s surface area and slowly loosen the post in its concrete footing. We reset the post, realign the hinges, and the gate swings properly again. In most cases, you don’t need a new gate. In a minority of cases where rust has degraded the frame around the hinge mounts, replacement is more economical than repeated repairs. We’ll tell you which applies to your gate. Call (833) 545-6817 for a free evaluation.
Yes. We service solar gate openers from all nine brands we carry parts for, and they’re common in San Clemente on hillside lots where running a power line to the gate would cost more than the opener itself. Common issues we see locally include corroded battery terminals from marine layer moisture, failed charge controllers, and panels angled wrong for winter sun. If your solar gate is getting weak or intermittent, call (833) 545-6817 and we’ll diagnose it.
Call Wrought Gate Repair for Gate Repair in San Clemente
We recently repaired a LiftMaster swing gate in Talega where the operator’s control board had failed due to corrosion from marine layer moisture. After replacing the board and applying a coastal-grade coating to the exposed terminals, we also performed sag correction on the hinge post, which had loosened from Santa Ana winds. The gate now operates smoothly and matches the HOA’s approved bronze finish. That’s the standard we hold for every San Clemente repair.
If your gate is rusting, sagging, sticking, or stopped responding to its remote, call us at (833) 545-6817 for a free estimate. We work exclusively on gates, and we service all of San Clemente, including 92672, 92673, and 92674. Your gate, fixed right. Reach out to our Gate Repair team today.
Written by Ruben Castellano, Owner at Wrought Gate Repair, serving San Clemente and surrounding Orange County communities.