Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Chino?
Gate Installation services in Chino typically run $2,400 to $8,500 for a standard residential driveway gate with an opener, and $1,000 to $2,200 for a smaller pedestrian or side-yard gate. Custom wrought iron driveway gates with automation on a large lot can reach $12,000 or more. The biggest cost swings come from gate width, material, and whether you’re adding an electric actuator or keeping it manual.
We work exclusively on gates, and we install across Chino daily. If you want a number for your specific property, call (833) 545-6817 for a free estimate. We’ll walk your gate line, measure the opening, and give you a written price the same visit.
Key Takeaways
- Most Chino homeowners pay $2,400 to $8,500 for a new automated driveway gate, installed.
- Manual pedestrian gates run $1,000 to $2,200. Automation adds $900 to $2,800 depending on the opener brand.
- Slope, old concrete, and permit requirements are the three things that push Chino projects up.
- We service nine gate automation brands, including LiftMaster, FAAC, BFT, DoorKing, and Ghost Controls, so you’re not locked into one dealer.
- Free estimates. Call (833) 545-6817.
Gate Installation Cost Breakdown (2026)
Here’s what a real installation breaks into. These ranges reflect Chino material and labor costs as of 2026, including typical disposal of an old gate and standard site prep.
| Line Item | Typical Range | What It Covers |
|---|---|---|
| Pedestrian / side-entry gate (manual) | $1,000 – $2,200 | 4 to 5 ft gate, posts, frame, hinges, install |
| Driveway gate (manual, single swing) | $2,400 – $5,000 | 12 to 16 ft wrought iron or ornamental steel, two posts set in concrete |
| Driveway gate (double swing, manual) | $3,800 – $7,200 | Two leaves, center latch, posts, install |
| Sliding gate (manual) | $3,200 – $6,500 | Track or cantilever system, posts, rollers, install |
| Swing opener (residential arm or articulated) | $900 – $1,900 | Actuator, control board, safety sensors, install |
| Slide opener | $1,200 – $2,400 | Slide actuator, rack, control board, sensors |
| Safety sensor package (photo-eye, loop, edge) | $250 – $650 | One or more safety devices, wired into control board |
| Keypad, remote, or entry intercom | $150 – $700 | One entry device, wired or wireless |
| Concrete pad or footing work | $400 – $1,600 | Cutting, removal of old concrete, new footings |
| Permit (City of Chino) | $150 – $450 | Plan check, inspection, permit issuance |
Add $500 to $1,800 to any row above if you’re replacing an old gate and its posts, since removal and site restoration take time and disposal. Custom ironwork, powder coating in a non-standard color, or matched ornamental patterns from a specialty fabricator can bump the material line higher.
We build the estimate from the actual measurements, so the number we write down is the number you’ll pay unless something’s buried under the concrete we didn’t know about. If we find a surprise, we stop and call you.
What Affects Gate Installation Pricing in Chino
Chino isn’t a flat grid, and the property quirks matter. Here’s what moves the price.
- Gate width and weight. A 16-foot wrought iron driveway gate needs heavier posts, bigger hinges, and a stronger opener than a 12-foot gate. Each additional foot on the span adds hardware cost and stress on the frame, and that stress shows up on the invoice.
- Slope and drainage. Chino has properties on grade, especially toward the Chino Hills side and older ranch lots off Euclid and Riverside Drive. A sloped gate line means custom-fabricated posts or leveling work, which adds $400 to $1,500 to a typical install.
- Old concrete and underground surprises. Lots built in the 1970s and 1980s around downtown Chino often have old fence footings, sprinkler mains, or utility runs right where the posts need to go. Cutting through and re-routing is real labor, usually $200 to $600 per post when the ground is busy.
- Material choice. Wrought iron and ornamental steel run higher than wood or aluminum but need fewer repairs over 20 years, which most Chino homeowners care about given the sun exposure. Powder-coated aluminum is the mid-price option; bare steel sheds paint faster in the Inland Empire heat.
- Automation brand and features. A LiftMaster or Linear swing opener is the price baseline. FAAC and BFT commercial-grade actuators cost more but hold up better on wide, heavy gates and in high-cycle use, which matters for HOA and commercial properties.
- City of Chino permit and code requirements. Driveway gates near a public sidewalk typically need a permit, and the City requires the gate to open inward, away from the street, unless your lot has a specific clearance exception. Plan on $150 to $450 in permit cost and a short wait for inspection.
For a deeper look at the installation process itself, see our page on Gate Installation in Chino.
How to Save on Gate Installation
There are real ways to bring the bill down without cutting into the quality of the gate. Our installers will tell you which is worth doing.
- Keep your existing posts if they’re sound. On a replacement, the most expensive hidden cost is pulling and resetting posts. If the posts are solid, plumb, and properly set in concrete, keeping them can save $400 to $1,200 on the job.
- Pick a standard-size gate. Custom-fabricated widths (say 13 feet instead of 12) add material and fabrication cost. Standard spans come off the racks cheaper and install faster.
- Bundle automation with installation. Adding the opener to the initial install costs less than retrofitting a manual gate later, since the wiring, conduit, and control board can go in during the same visit.
- Choose a brand we already service. Because we work on nine major automation brands (LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule), we’re not marking up for a brand we don’t stock parts for. That’s a real cost difference when a warranty repair or sensor swap comes up.
- Get a free estimate early. We’ve seen plenty of Chino homeowners pay for a “repair” that should have been an install, or vice versa. An honest assessment in month one is cheaper than a failed gate in month six. Call (833) 545-6817 for a free estimate before you commit to anything.
If your current gate is on its last legs, it’s worth comparing repair versus replacement before you decide. Our electric gate repair in Chino page walks through what’s repairable and when a new install makes more sense.
FAQs – Gate Installation Cost
How much does a driveway gate cost in Chino in 2026?
A driveway gate in Chino runs $2,400 to $8,500 installed, with most single-swing projects landing around $3,200 to $5,500 and double-swing or sliding gates at the higher end. Automation adds $900 to $2,800 on top. Call (833) 545-6817 for an exact written quote after we measure your gate line. Estimates are free.
Is it cheaper to repair my existing gate or install a new one?
Repair is cheaper when the frame and posts are structurally sound; a typical opener or hinge repair runs $180 to $650. A new install becomes the better value when the gate frame is bent, the posts are rotted or pulling out of concrete, or the gate has been repaired more than twice in five years. We give you both numbers and a straight recommendation. Call (833) 545-6817 and we’ll tell you which way your gate leans.
How much does an electric gate opener cost to install in Chino?
An electric swing opener costs $900 to $1,900 installed in Chino, and a slide opener runs $1,200 to $2,400, including the actuator, control board, and safety sensors. FAAC and BFT actuators sit at the top of that range; LiftMaster and Linear land in the middle. Call (833) 545-6817 and we’ll quote the opener that fits your gate’s weight and width.
Can you install my gate the same day I call?
Not for a new install. A standard driveway gate install is scheduled within a few days of your estimate because posts need to set in concrete before the gate and opener go on. Emergency repairs on an existing gate can often be handled the same or next day. Call (833) 545-6817 to schedule, and we’ll give you a real date, not a range.
Do I need a permit to install a gate in Chino?
Yes, if your gate is near a public sidewalk or crosses a driveway approach. The City of Chino requires a permit for driveway gates, and the inspector will check set-back and the inward-opening rule on your lot. Plan on $150 to $450 for the permit and one inspection. We handle the paperwork as part of the install. Call (833) 545-6817 with questions before you file.
What We Bring to a Chino Gate Install
We’re not a general contractor that also hangs gates. Every technician, every tool, and every part on the truck is focused on gates. That means when your gate is a bent wrought iron swing off a 1970s ranch, or a modern sliding gate with a FAAC actuator, we’ve seen the failure mode before and know exactly what to do about it.
This is the home page for everything we do, and it’s the fastest way to see the full scope: gate repair, electric gate repair, and new installation. One company, one call, one crew from the estimate through the final test of the opener.
We know Chino. We’ll measure on site, we’ll quote before we touch a wrench, and we’ll tell you honestly if your existing gate is worth saving. That’s the whole pitch.
If you’re ready to talk about a new gate, call (833) 545-6817. Free estimates, written upfront, no pressure to sign on the spot.
Pricing reflects the Chino market as of 2026. Wrought Gate Repair offers free estimates – call (833) 545-6817.
What Our Customers Say
"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
— Marisol Flores"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Gilbert Delgado"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
— Carlos Salazar