Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Chino?
Gate repair in Chino typically runs $150 to $650 for most residential jobs, while electric gate repairs more commonly land between $250 and $900 depending on the opener brand and the part that failed. Simple fixes like a hinge, latch, or wheel replacement usually come in under $250, and a full opener board or motor replacement on a LiftMaster or FAAC swing gate can push past $1,200. The honest number we give every Chino customer is this: most repair visits finish between $180 and $500, and we tell you the price before we touch anything.
We work exclusively on gates, so the estimate you get from us is based on the specific system in front of us, not a generalist’s guess. Whether it’s a manual wrought iron driveway gate on a horse property off Chino-Corona Road or a DoorKing slide gate at a commercial lot off Central Avenue, one call covers it.
Key Takeaways
- Most residential gate repairs in Chino cost $150 to $650.
- Electric and automated gate repairs usually run $250 to $900, with motor and board replacements at the higher end.
- Manual iron gate repair is often the cheapest fix; opener electronics drive the bill up fastest.
- We service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Free estimates in Chino: (833) 545-6817.
Gate Repair Cost Breakdown (2026)
Here’s what the line items actually cost in the Chino market this year. These ranges reflect real repair scope, parts, and labor for residential and light commercial gate systems.
| Repair Type | Typical Cost Range |
|---|---|
| Hinge repair or replacement | $120 – $280 |
| Latch, striker, or handle repair | $95 – $220 |
| Gate wheel or roller replacement | $130 – $300 |
| Gate sagging / alignment correction | $180 – $420 |
| Wrought iron panel straightening or hinge re-weld | $200 – $550 |
| Electric gate opener repair (arm, chain, sensor) | $220 – $600 |
| Gate control board or receiver replacement | $280 – $650 |
| Opener motor / actuator replacement (LiftMaster, FAAC, BFT) | $550 – $1,200 |
| Safety sensor, loop, or photo-eye recalibration | $150 – $400 |
| Full gate replacement (if repair isn’t viable) | $1,800 – $6,500+ |
What pushes a bill toward the top of these ranges? Two things mainly: the brand of your opener and whether the part is a special order. FAAC and BFT actuators, for example, sometimes need a factory component we don’t keep on the truck, and that adds days and dollars. Standard LiftMaster and Linear parts are usually in stock and can be swapped the same visit. A manual wrought iron gate is almost always cheaper to fix than an automated one because there’s no electronics in the equation. Commercial slide gates with loop-detection and DoorKing entry systems sit at the higher end because there’s more to diagnose and more safety hardware involved.
When you want a firm number rather than a range, we offer free on-site estimates across Chino. See our full Gate Repair in Chino service page for what a visit includes, or call (833) 545-6817.
What Affects Gate Repair Pricing in Chino
Chino isn’t a generic market. The mix of older ranch properties, newer HOA communities, and commercial corridors along Central and Chino Hills Parkway shapes the price in specific ways. Here’s what moves the number up or down.
- Manual vs. motorized. A manual wrought iron gate needing a hinge or wheel fix is the cheapest repair we do, often $120 to $250. The moment an opener is involved, diagnosis time and part cost climb. Electric gate work typically starts around $220 and goes up from there.
- Opener brand and part availability. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Common brands with local parts stock keep the bill low; less common actuators that need a special-order component cost more and take longer.
- Gate material and weight. Heavy wrought iron and commercial steel gates take more labor to realign, re-hang, or correct when they sag. A light aluminum residential gate is faster to work on. Our name points at the trade we know best: iron and metal gates.
- Site access and gate size. A wide driveway slide gate on a large lot is a bigger job to service than a pedestrian walk gate. Tight lots and long gate runs add setup and travel time.
- Whether it’s a safety or code issue. Photo-eye sensors, safety loops, and auto-reverse on an automated gate are there for a reason. When those fail, the repair isn’t optional and often involves recalibrating the whole system, which adds cost but keeps the gate safe.
- Repair vs. replace decision. If the frame is bent or rusted through, a repair won’t hold. That’s where a replacement quote comes in. We’ll tell you straight if patching is throwing money at a gate that’s past saving.
Why We Cost What We Cost (and Why It’s Worth It)
You’ll find handymen and fence companies quoting gate work cheaper. Here’s the difference. We work exclusively on gates. Every technician, every tool on the truck, and every part we carry is focused on gate systems, not split across fencing, garage doors, and general contracting. That focus is why we can diagnose a FAAC actuator fault the same day a generalist would be calling around for a manual.
It’s also why we can service all nine major brands under one roof. If your gate has a Mighty Mule swing arm, a Ghost Controls operator, or a Viking actuator, you don’t need to track down a brand-specific dealer and wait a week. One call covers it, and one company stays accountable from the first assessment through the repair, or through a full installation if that’s the right call. No handoffs, no referrals out.
The “wrought” in our name isn’t decoration. It anchors us in ironwork precision, and it sets the expectation that we fix gates to last rather than patch them to get you off the phone. If you want the cheapest possible fix from someone who mostly installs fences, that’s a different business. If you want your gate fixed right by people who only do gates, that’s us.
How to Save on Gate Repair
There are real ways to keep the bill down without cutting corners on the parts that matter. A few that actually work in Chino:
- Catch it early. A gate that’s starting to sag or drag is a $180 alignment job. Wait until the hinge tears out of the post and you’re looking at a weld or a post rebuild. Small problems get expensive fast.
- Fix manual issues before they become automation problems. A dragging manual gate strains an opener’s motor once you automate it. Get the mechanical side right first.
- Bundle the work. If two hinges and a latch are all failing, fixing them in one visit costs less than three separate trips. Ask us to look over the whole gate, not just the one symptom.
- Keep the opener brand serviceable. Stick with the widely serviced brands we carry parts for when it’s time to replace, so future repairs stay fast and affordable.
- Get the estimate before the work. We give free, upfront estimates, so there’s no surprise line item at the end. Call (833) 545-6817 and we’ll price it before we start.
We don’t pad estimates to sell a replacement you don’t need, and we don’t lowball to win the job and surprise you later. For a straight read on whether your gate needs a repair or a replacement, book a free estimate and we’ll walk you through the trade-offs on your property.
Gate Repair Pricing by System Type in Chino
Different gate systems fail in different ways, and the price follows the failure. Here’s how the two main categories break down.
Manual Gate Repair
Manual wrought iron and metal gates are the simplest and most affordable to fix. Common jobs include hinge replacement, welding a cracked frame, replacing a gate wheel on a slide gate, and re-aligning a gate that’s dropped and dragging on the ground. Most manual repairs in Chino fall between $150 and $450. Older iron gates on horse properties and ranch lots around the city are frequent candidates for re-welding and re-hanging.
Electric and Automated Gate Repair
Automated systems add a layer of diagnosis. When a gate stops opening, the fault could be the opener motor, the control board, the safety sensors, a wiring issue, or the gate’s own mechanical drag. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so we identify the fault and fix the electronics or the mechanics behind it. Electric gate repairs in Chino usually run $250 to $900, with motor and actuator replacements landing at the top of that range. Commercial DoorKing entry systems and slide gates with safety loops sit higher because there’s more hardware to diagnose.
Repair or Replace: How to Decide
This is the question that changes the budget most, so here’s the straight talk. Repair usually wins when the frame and posts are structurally sound and the failure is mechanical or electronic: a bad hinge, a dead opener, a failed sensor. Replace it when the frame is bent, rusted through, or the posts are failing, because a repair won’t hold and you’ll be back in six months.
As a rule of thumb we use: if a repair costs more than half of a new gate and the existing gate is already showing structural wear, replacement usually makes more sense. If the gate is solid and only one part failed, repair is almost always the better money. We’ll give you both numbers in the same free estimate so you can decide with the facts in front of you, not a sales pitch. For new gate work, our installation service covers manual and automated systems start to finish.
FAQs – Gate Repair Cost in Chino
How much does gate repair cost in Chino?
Most gate repairs in Chino cost between $150 and $650 for residential work, with electric gate repairs typically running $250 to $900. Simple manual fixes like a hinge or wheel replacement start around $120. Call (833) 545-6817 for a free estimate and an exact number for your gate.
Is it cheaper to repair or replace a gate?
Repair is usually cheaper when the frame and posts are sound and only the hardware or electronics failed, often $150 to $650 versus $1,800 to $6,500+ for a new gate. Replacement makes more sense when the frame is bent or rusted. A free estimate gives you both numbers side by side.
Do you charge for estimates in Chino?
No. Our estimates are free and pricing is upfront, so you know the cost before any work starts. Call (833) 545-6817 to schedule one.
Can you repair my gate the same day?
Usually, yes, for common issues where we have the part on the truck. Standard LiftMaster, Linear, and manual gate repairs are often completed the same visit, while special-order parts for brands like FAAC or BFT can add a few days. Call (833) 545-6817 and we’ll tell you what your specific gate needs.
Do you fix electric gates, or only manual ones?
Both. We repair manual wrought iron and metal gates and service electric and automated systems across nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. One call covers manual or motorized. Call (833) 545-6817 for a free estimate.
Get Your Gate Fixed Without the Guesswork
You don’t need five quotes and a generalist’s best guess. Whether your gate is manual or motorized, a sagging wrought iron driveway gate or a commercial DoorKing entry system that stopped cycling, one call covers it. We bring gate-only focus, nine-brand service capability, and free, upfront estimates. Call (833) 545-6817 today and we’ll price the job before we start, so the number you hear is the number you pay. Your gate, fixed right.
Pricing reflects the Chino market as of 2026. Wrought Gate Repair offers free estimates – call (833) 545-6817.
What Our Customers Say
"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
— Priya Mehta"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Jasmine Coleman"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
— Marisol Flores